产品导览
OTP ADC Type MCU Series (High EFT/ESD Level)
产品资讯
- 封装尺寸
联络我们
一般描述
特征
- CPU Configuration
- 6K×13 bits on-chip ROM
- 272×8 bits on-chip registers
- 8-level stacks for subroutine nesting
- Dual clock operation mode
- Four operation modes: Normal, Green, Idle, & Sleep
- Two programmable Level Voltage Detector (LVD): 2.3V, 3.0V
- Power-on reset Level Voltage: 1.9 reset level, 2.0 release
- Less than 2.0 mA at 3.3V / 4 MHz
- Typically 15 μA, at 3V / 32kHz
- Typically 2 μA, during Sleep mode
- I/O Port Configuration
- 6 bidirectional I/O ports: P7, P8, P9, PA, PB and PC
- 45 I/O pins & 1I pin
- 45 programmable pull-high I/O pins
- 39 programmable open-drain I/O pins
- External interrupt with Wake-up : P74~P77, P82~P83, PB0~PB3
- Operating Voltage
- 2.2V~3.6V at -40°C~85°C (Industrial)
- Operating Frequency
- Crystal/IRC/ERC oscillation circuit selected by code option for system clock
- IRC oscillation circuit selected by code option or register
* Main Clock
- Crystal mode:
DC~20 MHz/2clks@3.3V;
DC~100ns inst. cycle @ 3.3V;
DC~16 MHz/2 clks @ 2.2V;
DC~250ns inst. cycle @ 2.2V
- ERC mode:
- IRC mode: DC~16 MHz/2 clks @ 2.2V ;
DC~400ns inst. cycle @ 2.2V
* Sub Clock
IRC mode : 16kHz
All these four main frequencies can be trimmed by programming with four calibrated bits in the ICE330N Simulator. OTP is auto trimmed by ELAN Writer
- Special features
- Programmable free running watchdog timer
- High ESD immunity
- Power saving Sleep mode
- Selectable Oscillation mode
- Peripheral configuration
- One clock output pin can output the currently working frequency
- 8-bit real time clock/counter (TCC)
- 24-channel Analog-to-Digital Converter (ADC) with 12-bit resolution in Vref mode
- Three 8-bit timers
- 8-bit Timer 1, auto reload counter/timer which can be an interrupt source. Function modes: Timer, Toggle output, UART baud rate generator, Capture, & PWM
- 8-bit Timer 2, auto reload timer which can be an interrupt source. Function modes: Timer, SPI baud rate generator, & PWM
- Two sets of 8 bits auto reload counter/timer which can be cascaded to one 16-bit counter/timer
- 8-bit Timer 3 with external clock source, can generate a 50% duty pulse output from T3OUT Pin.
- Universal Asynchronous Receiver/Transmitter (UART) available (operates at 16 MHz/2Mbps, 2.2V)
- I2C-bus function, including 7-bit/10-bit address 8-bit data transmit/ receive mode and 16 bytes buffer to save the data.
- Serial Peripheral Interface (SPI)
- Digital-to-Analog Converter (DAC) current type with 10-bit resolution
-
Single instruction cycle commands
- 22 available interrupts: 10 external, 12 internal
- TCC overflow interrupt
- Ten external interrupts (wake-up from sleep mode)
- Three timer interrupts
- A/D converter interrupt
- SPI interrupt
- Two I2C interrupts
- Three UART interrupts
- Low voltage detect (LVD)
Note: Green products do not contain hazardous substances.